No heat? Call (780) 809-9782Smell gas? Leave the house, then call 911 or ATCO 1-800-511-3447

Home / Guides / Furnace problems

Furnace clicking but no heat: what to check

Clicking is a normal part of many furnace start-ups, so the sound alone is not the problem. Clicking over and over with no flame and no heat is the problem. It usually means the furnace is trying to light and not succeeding.

If you smell gas, do not keep trying to start the furnace. Leave the building and call ATCO Gas at 1-800-511-3447 or 911 from a safe distance. A CO alarm sounding is also a reason to get outside first.

Clicking that is normal and clicking that is not

FurnacePrices.ca says clicking while the furnace is simply heating up is normal. It becomes a concern when it is persistent, excessive, louder or changing, and the site ties that kind of clicking to the ignition system. So the question to answer is whether the burners ever light after the clicks.

Common reasons a furnace clicks without lighting

  • Thermostat settings: Trane says to confirm the thermostat is on heat with a setpoint above the room temperature.
  • Gas supply: the shutoff valve near the furnace may be closed. Trane says the knob or lever should be in the on position.
  • Igniter: Trane notes furnaces made since 2010 use an electronic igniter, and a failed one needs professional troubleshooting.
  • Flame sensor: a dirty or faulty sensor can prevent ignition because the furnace cannot confirm a flame.
  • Dirty burners or a restricted filter: Trane lists both as causes that stop the sequence.

Step by step checks

  1. Check the thermostat: heat mode, setpoint above the indoor reading, and fresh batteries if it uses them.
  2. Confirm the furnace switch is on and the breaker has not tripped. If it has tripped, Trane advises not to reset it repeatedly and to call an HVAC professional.
  3. Look at the air filter and replace it if dirty. Trane suggests changing filters every 1 to 3 months.
  4. Check the gas shutoff valve near the furnace. If you cannot tell whether it is on, ask a professional rather than guessing.
  5. Give the furnace one more full cycle and note whether it clicks, lights briefly, or does nothing.

What the sequence tells you

A gas furnace has to light the burners and then confirm the flame before it keeps the gas flowing. Clicking with no flame suggests the sequence stalls at the lighting step. Burners that light for a few seconds and then go out suggest the flame is not being confirmed.

Trane describes the flame sensor as a safety device that detects flame and shuts off gas if none is found, and says cleaning or replacing it should be left to professionals.

Pilot-equipped furnaces

Trane says furnaces built before 2010 may use a standing pilot, and that a pilot that has gone out can be relit following the manufacturer guide. If yours has a pilot, see our pilot light guide for the safe steps and when to stop. Never relight if there is any smell of gas.

What not to do

  • Do not open the furnace and clean burners yourself. Trane warns this may void the warranty and should be done by an HVAC company.
  • Do not bypass safety switches or jumper controls.
  • Do not keep cycling the thermostat dozens of times hoping it will catch. Repeated failed starts mean the problem is real.

Want numbers? Try the cost calculator or the repair-or-replace tool.

Frequently asked questions

Why does my furnace click and then nothing happens?

The click is often the igniter or a relay trying to start the sequence. If no flame follows, common causes include a failed igniter, a dirty flame sensor, a closed gas valve or a thermostat setting issue. Trane lists each of these.

Is it okay to reset the breaker?

Trane advises against repeated resets and says to call a professional if the breaker has tripped, since a trip likely points to a furnace problem.

How do I know if I have an electronic igniter or a pilot?

Trane says furnaces made since 2010 use electronic igniters, and older ones may use a standing pilot. The label or manual on your furnace will say which you have.

Will a tune-up prevent this?

It can help catch worn igniters and dirty sensors early. Trane says a yearly tune-up lets a technician check the igniter, burners and control board.

Sources

  1. FurnacePrices.ca: common causes and solutions for furnace noises
  2. Trane: furnace not igniting troubleshooting

Figures are guides, not quotes. Prices and rules change; confirm with your contractor and the City of Edmonton. Last reviewed November 2026.

Need heat back on in Edmonton?

Call now to reach a local technician, or send a quick request.

Call nowQuote