No heat? Call (780) 809-9782Smell gas? Leave the house, then call 911 or ATCO 1-800-511-3447

Home / Guides / Furnace problems

Furnace keeps tripping the breaker: what to know

A breaker is a safety device. When it trips, it is saying the circuit carried more current than it should, or that something is faulty. With a furnace, the right response is to find out why, not to keep flipping it back on.

If you see scorch marks, smell burning plastic, feel a hot outlet or switch, or smell gas, do not touch the breaker or furnace. Move outside and call 911, or ATCO Gas at 1-800-511-3447 for gas odors.

Two manufacturers, two slightly different first steps

Carrier Canada says to check the circuit breaker or fuse box to make sure the furnace is getting power, and to reset a tripped breaker. Trane takes a more cautious line: if the breaker has tripped, avoid resetting it and call an HVAC professional, since the trip likely points to a furnace problem. The safest middle ground is to reset at most once, and to stop if it trips again.

Why a furnace breaker trips

  • A failing blower motor or other motor drawing too much current. Carrier Canada says blower motor repair may be a major job worth weighing against replacement.
  • A restricted airflow problem that makes the motor work harder, such as a very dirty filter. Natural Resources Canada warns a dirty filter can increase energy costs and damage the system.
  • A fault in wiring, a loose connection or a failing control component, which needs a qualified technician.
  • A shared circuit with other loads. If the furnace is on a circuit with other equipment, the combined load can trip it.
  • A breaker that is itself worn and tripping at lower loads than it should. A licensed electrician can test it.

Checks that are safe

  1. Confirm the furnace switch, usually on or near the unit, is on.
  2. Check the breaker panel. Note which breaker tripped and whether it feels warm.
  3. Check and replace the air filter if dirty. Trane suggests changing it every 1 to 3 months.
  4. If you reset the breaker and it trips again right away, stop. Leave it off and call a professional.
  5. Do not tape, jam or replace a breaker with a larger one. That removes protection the wiring depends on.

Timing clues worth noting

It helps a technician if you can say when the breaker tripped. If it trips the instant the furnace starts, the blower motor or a short in a component is a suspect. If it trips after the furnace has run for a while, something may be overheating or drawing more current as it warms. If it trips only when other appliances run, the circuit may be shared or overloaded.

Also note any other symptoms before the trip, such as a squeal from the blower, burning smells or the furnace cycling on and off. Our pages on short cycling and furnace noises cover related causes.

Who should do the repair

Furnace electrical work crosses two trades: heating and electrical. Natural Resources Canada recommends a licensed, insured contractor for annual checks, including whether the unit starts, runs and shuts off properly. If the issue is in the panel or the circuit, a licensed electrician may be needed. In Alberta, ask who is responsible for permits if wiring or gas components are changed.

Costs and decisions

Costs depend on the cause, from a simple filter and reset to a motor or control repair. Get a written diagnosis before work begins. If the furnace is older and the cause is a blower motor, Carrier Canada suggests weighing the repair against replacement.

Want numbers? Try the cost calculator or the repair-or-replace tool.

Frequently asked questions

Is it safe to reset the breaker?

Manufacturers differ. Carrier Canada says to reset a tripped breaker, while Trane advises avoiding a reset and calling a professional. If it trips a second time, stop and get a technician.

Could a dirty filter trip the breaker?

A dirty filter restricts airflow and can make the system work harder. Natural Resources Canada says a dirty filter can increase energy costs and damage the system, so replacing it is a reasonable first check.

Can I swap in a bigger breaker?

No. The breaker is sized to protect the wiring. Changing it is an electrician job and should not be done to stop nuisance trips.

Should I call an electrician or an HVAC company?

Start with an HVAC technician if the trip seems tied to the furnace running. If they find the furnace is fine, a licensed electrician can test the circuit and breaker.

Sources

  1. Carrier Canada: troubleshooting your gas furnace
  2. Trane: furnace not igniting troubleshooting
  3. Natural Resources Canada: guide to maintaining your home heating and cooling system

Figures are guides, not quotes. Prices and rules change; confirm with your contractor and the City of Edmonton. Last reviewed November 2026.

Need heat back on in Edmonton?

Call now to reach a local technician, or send a quick request.

Call nowQuote