No heat? Call (587) 741-8880Smell gas? Leave the house, then call 911 or ATCO 1-800-511-3447

Home / Guides / Safety

Furnace yellow flame: what it means and what to do

A natural gas furnace flame should be a steady, clear blue. A flame that is yellow, orange or floppy can mean the gas is not burning completely, which is how carbon monoxide is produced. Both ATCO Gas and the Canadian Gas Association tell homeowners to treat a yellow burner flame as a reason to call a qualified technician.

If a carbon monoxide alarm is sounding, or anyone feels dizzy, nauseous or has a headache, get everyone outside and call 911. If you smell gas, leave and call ATCO Gas at 1-800-511-3447 or 911.

What a healthy flame looks like

ATCO Gas says to check your furnace flame monthly and that you should see a clear blue flame. A utility guide from Jackson Energy Authority describes a healthy flame as blue, sometimes with a tiny tip of yellow. The furnace burners are behind a small viewing window or a panel. If you are not sure how to look at them safely, a technician can show you during a service visit.

A yellow or orange flame, or one that keeps popping with bursts of yellow, points to the wrong mix of air and gas. That means combustion is incomplete.

Why a yellow flame matters

Carbon monoxide is a colourless, odourless, tasteless gas produced when fuel burns incompletely. Health Canada notes that it reduces the blood's ability to carry oxygen and can affect you before you notice it. ATCO lists furnaces and other natural gas appliances among the sources of CO when they operate improperly, and lists headache, dizziness, fatigue, nausea and loss of muscle control among the symptoms.

Other warning signs to look for

  • Soot or water collecting near a burner or vent, which ATCO says to watch for during visual checks.
  • A pilot light that keeps going out. ATCO says to turn the appliance off and call ATCO Gas or a qualified heating contractor.
  • Stale or stuffy air, excess moisture on windows and walls, or soot around appliances and vents, listed in an ATCO brochure produced with the Alberta Fire Chiefs Association.
  • A CO alarm that goes off, even once.

What to do if you see a yellow flame

  1. Turn the furnace off at its switch or the thermostat. The Canadian Gas Association says to turn off the appliance and contact a registered fuels contractor.
  2. If anyone has symptoms such as headache, dizziness or nausea, go outside and call 911.
  3. Check that your CO alarm is working. See where to place CO alarms in Alberta.
  4. Call ATCO Gas or a qualified heating contractor to inspect the furnace before using it again.
  5. Do not try to adjust the burners or gas pressure yourself.

Common causes a technician will look for

A utility guide notes that a brief yellow flame can come from dust particles or a dirty burner, and that a flame that stays yellow or orange needs a professional. A technician will inspect the burners, the gas supply, the venting and the heat exchanger, and will measure combustion rather than judging by eye alone. A blocked vent or restricted air supply can also cause poor combustion, which is why ATCO says never to plug or cover vents that supply air to gas appliances and to keep the area around the furnace clear of clutter.

How to lower the risk going forward

  • Have your furnace checked regularly by a qualified technician according to the manufacturer's specifications, as ATCO recommends. See furnace tune-up cost in Edmonton.
  • Replace or clean the filter monthly during heating season.
  • Keep furnace panels and grills in place.
  • Install and regularly test CO alarms, and replace them as the manufacturer recommends.
  • Never idle a vehicle in an attached garage, even with the door open.

A fine-looking flame does not prove the furnace is safe

Flame colour is a useful clue, not a full test. A cracked heat exchanger or a partly blocked flue can be a problem even when the burners look blue. That is why a CO alarm and regular professional checks matter together. For more on CO risks from furnaces in Alberta, see carbon monoxide and furnaces in Alberta.

Want numbers? Try the cost calculator or the repair-or-replace tool.

Frequently asked questions

Is a yellow flame on a furnace always carbon monoxide?

Not always, but it means combustion may be incomplete and carbon monoxide may be produced. ATCO and the Canadian Gas Association both say to turn the appliance off and call a qualified technician.

Should the flame be blue or orange?

Blue. ATCO says a natural gas furnace should show a clear blue flame, and a yellow flame means the fuel is not burning completely.

Can I keep using the furnace until a technician arrives?

ATCO's guidance is to turn the appliance off and call ATCO Gas or a qualified heating contractor. If you have no heat, ask the technician or ATCO about safe options, and do not use outdoor fuel-burning equipment indoors, which Health Canada lists as a CO risk.

Do gas fireplaces have yellow flames?

Some decorative gas fireplaces are designed with a yellow flame for appearance, which is different from a furnace burner. If you are unsure, check the appliance manual or ask a technician.

Sources

  1. ATCO Gas: carbon monoxide
  2. Canadian Gas Association: safety at home
  3. Health Canada: carbon monoxide overview
  4. Jackson Energy Authority: proper flame

Figures are guides, not quotes. Prices and rules change; confirm with your contractor and the City of Edmonton. Last reviewed November 2026.

Need heat back on in Edmonton?

Call now to reach a local technician, or send a quick request.

Call nowQuote