No heat? Call (587) 741-8880Smell gas? Leave the house, then call 911 or ATCO 1-800-511-3447

Home / Guides / Furnace problems

Furnace blowing cold air: causes and what to do

Cold air from the vents in a Edmonton winter is stressful. Most causes are simple. A few need a technician. Here is how to tell which is which.

Smell gas or hear a CO alarm? Leave the house first, then call 911 or ATCO Gas at 1-800-511-3447. Do not keep troubleshooting.

Check these first (about five minutes)

  1. Thermostat: make sure it is set to Heat and above room temperature. If the screen is blank, replace the batteries.
  2. Fan setting: if the thermostat fan is set to On instead of Auto, the fan can blow unheated air between heating cycles.
  3. Power: check the furnace switch (it looks like a light switch near the unit) and the breaker.
  4. Filter: a badly clogged filter restricts airflow and can make the furnace shut its burners off to protect itself.
  5. Outside pipes: make sure the intake and exhaust pipes on the outside wall are not blocked by snow or ice.

Common causes a technician fixes

  • Dirty or failed flame sensor: the burners light, then shut off, so the blower runs without heat. Typical repair $75 to $200.
  • Failed igniter: the burners never light. Typical repair $150 to $300.
  • Gas valve problem: no gas reaches the burners. Typical repair $300 to $700.
  • Overheating from restricted airflow: closed or blocked vents, a dirty filter or a failing blower can trip the limit switch.
  • No gas supply: if the stove or water heater also do not work, call ATCO Gas at 1-800-511-3447.

What a diagnostic visit costs

A diagnostic or service call typically runs $80 to $150 in published Canadian price guides. Ask whether the fee is credited toward the repair. See the full list in the furnace repair cost guide.

When to think about replacement

If the furnace is past 15 years old and keeps failing, or the repair quote is 50 percent or more of a new unit, replacement can make more sense. The repair-or-replace tool walks through it in six questions.

Cold air only at the start, or all the time?

Notice when the cold air happens. Cool air for the first minute or so after the blower starts can be normal, because a modern furnace waits for the heat exchanger to warm up before running the fan at full speed. Air that stays cold for the whole cycle points to burners that are not lighting or are shutting off, and that is worth a closer look.

Also note whether the air is lukewarm rather than cold. Lukewarm air often means the furnace is lighting but cycling off early on a safety limit, which is a different problem from a furnace that never fires.

Signs that point to each cause

What you noticeLikely direction
Blower runs, no clicking or flame at startIgniter or control problem
Burners light briefly, then go outFlame sensor or airflow problem
Warm air for a while, then coldOverheating or limit switch
Cold air only when the fan setting is OnThermostat fan setting
No heat from other gas appliances eitherGas supply issue, call ATCO Gas

Look at the outside pipes in winter

High-efficiency furnaces draw air in and push exhaust out through plastic pipes that end on an outside wall. In a cold Edmonton snap, frost, drifting snow or a bird nest can block them, and the furnace shuts down as a safety measure. Clearing the opening gently by hand, without damaging the pipe, is a safe check. If you are not sure which pipes are the furnace's, leave them alone and ask a technician.

Keep the house safe while you wait

While waiting for a repair, keep the house closed up, use blankets and close doors to rooms you do not need. Do not use a gas oven, barbecue or camp stove for heat indoors, because they can release carbon monoxide. If you use a plug-in electric space heater, plug it directly into the wall and keep it clear of curtains and bedding.

Want numbers? Try the cost calculator or the repair-or-replace tool.

Frequently asked questions

Why is my furnace blowing cold air only sometimes?

Often the burners are shutting off early, which points to a dirty flame sensor, a clogged filter or restricted airflow. A fan set to On can also push unheated air between cycles.

Is it safe to keep running a furnace that blows cold air?

If there is no gas smell and no CO alarm, it is not an immediate danger, but you are not getting heat. Do not bypass safety switches. If anything smells like gas, leave and call 911 or ATCO.

Is cold air from the vents dangerous?

Cold air by itself is not dangerous, but a house that stays cold in winter is a risk for pipes and for people. If the cold air comes with a gas smell, soot or a CO alarm, leave the house and call 911 or ATCO Gas.

Should I reset the furnace?

Turning the furnace power switch off for a minute and back on is a reasonable check. If the problem comes back right away, stop and call a technician instead of repeating resets.

Sources

  1. ATCO Gas: outages and emergencies
  2. ATCO Gas: report a gas emergency (leave first, then call)
  3. HomeStars: furnace repair cost in Canada (2026)

Figures are guides, not quotes. Prices and rules change; confirm with your contractor and the City of Edmonton. Last reviewed November 2026.

Need heat back on in Edmonton?

Call now to reach a local technician, or send a quick request.

Call nowQuote