No heat? Call (587) 741-8880Smell gas? Leave the house, then call 911 or ATCO 1-800-511-3447

Home / Guides / Safety

Carbon monoxide alarm placement in Alberta homes

A carbon monoxide alarm is the only way to detect CO, because the gas has no smell, taste or colour. Where it goes matters. This page summarizes the placement rules in Alberta's safety codes publications and Health Canada's advice. It is general information, not legal advice, and your local fire department or safety codes authority has the final say for your home.

If a CO alarm sounds, leave the home right away and call 911. Health Canada's advice is to leave immediately when the alarm sounds.

Who the Alberta Building Code requires alarms for

Alberta Municipal Affairs and the Safety Codes Council state that the Alberta Building Code requires certified CO alarms in every building with a residential occupancy that also has a fuel-burning appliance, an attached storage garage, or both. That requirement applies to new construction. For existing homes, the Alberta publications say CO alarms are strongly recommended, and Health Canada advises at least one CO alarm with battery backup in any home with combustion appliances.

Fuel-burning appliances include a gas furnace, a gas water heater, a gas fireplace and a wood stove. Because most Edmonton homes have at least a gas furnace, an alarm makes sense in almost every house.

Where alarms go in a home with a fuel-burning appliance

  • Inside each bedroom, or outside each bedroom within 5 m (about 16 feet) of the bedroom door, measured along corridors and through doorways.
  • In a room containing a solid-fuel-burning appliance such as a wood stove, mounted at the height the manufacturer recommends or, if the manufacturer is silent, on or near the ceiling.
  • In each suite that shares a wall or floor and ceiling with a storage garage, inside each bedroom or within 5 m of each bedroom door.
  • In a service room housing a fuel-burning appliance when that room is not part of a suite, along with the adjacent suites, per the code text published by Alberta Municipal Affairs.

Health Canada's placement advice

Health Canada says the most important place to install a CO alarm is in hallways outside sleeping areas, and recommends an alarm with a digital display that shows low CO levels. A display can reveal a developing problem before the alarm threshold is reached. Follow the manufacturer's directions for installation, testing and replacement. Because CO mixes freely through indoor air, the exact mounting height depends on the product, which is why the code says alarms must be mechanically fixed at the height the manufacturer recommends.

Alarm requirements the code lists

  • The alarm must conform to CSA standard CAN/CSA 6.19, Residential Carbon Monoxide Alarming Devices. Look for the certification label on the box and alarm.
  • It must have an integral audible alarm.
  • It must be mechanically fixed to a surface, not just left on a shelf.
  • If it is powered by the home's wiring, there must be no disconnect switch between the overcurrent device and the alarm.
  • Battery-operated and hardwired alarms are both acceptable.
  • A combined smoke and CO alarm is acceptable if it meets both CAN/CSA 6.19 and CAN/ULC S531.

Secondary suites

The Safety Codes Council states that homes containing a secondary suite must have CO alarms in both the main dwelling and the secondary suite, hard-wired and interconnected so they operate in unison. If you rent out a basement suite, or are buying a home that has one, check this with your municipality before relying on an existing setup.

Test and replace on schedule

Health Canada says to test CO alarms regularly, replace batteries and the alarm as the manufacturer recommends, and write the installation and replacement dates on the device. Check the expiry date, because alarms do not last forever. Your alarm's manual explains what its chirps and display codes mean.

Alarms do not replace furnace maintenance

An alarm warns you after CO has built up. Preventing it matters more. ATCO Gas recommends having furnaces and other gas appliances checked regularly by a qualified technician and checking the flame for a clear blue colour. See furnace yellow flame and carbon monoxide and furnaces in Alberta, and furnace tune-up cost for what a service visit costs.

Want numbers? Try the cost calculator or the repair-or-replace tool.

Frequently asked questions

Are carbon monoxide alarms required in existing Alberta homes?

The Alberta Building Code requirement applies to new buildings. Alberta Municipal Affairs strongly recommends alarms in all existing homes, and Health Canada advises at least one alarm with battery backup wherever combustion appliances are used. Rental and municipal rules may add requirements, so confirm with your local authority.

How many CO alarms do I need?

The code places an alarm in or within 5 m of each bedroom door where a fuel-burning appliance is present. A multi-storey home with bedrooms on several levels needs coverage for each sleeping area. Health Canada says at least one alarm.

Can I use a combined smoke and CO alarm?

Yes, if it meets both CAN/CSA 6.19 for CO and CAN/ULC S531 for smoke, according to Alberta Municipal Affairs. A CO-only alarm does not detect smoke.

Where should I not put a CO alarm?

Placement details differ by model, so the manual is the authority. The code requires mounting at the manufacturer's recommended height.

Sources

  1. Alberta Municipal Affairs: Carbon Monoxide Home Installation (PDF)
  2. Safety Codes Council: Carbon Monoxide Alarm safety tips (PDF, 2020)
  3. Health Canada: carbon monoxide, preventing exposure
  4. ATCO Gas: carbon monoxide

Figures are guides, not quotes. Prices and rules change; confirm with your contractor and the City of Edmonton. Last reviewed November 2026.

Need heat back on in Edmonton?

Call now to reach a local technician, or send a quick request.

Call nowQuote